This listing is for custom 3D printed replacement accessories for the vintage Star Wars Imperial Shuttle. No original vintage parts or figures are included. Any vintage parts shown in the pictures are for comparison purposes only. Please read this whole description prior to buying. The parts you receive are very close to the original color. You do NOT need to paint these for them to look good - though they are not the EXACT original color. PLEASE SEE PICS. You can paint these parts if you desire custom colors. The parts available are:Canopy - does NOT come with glass. Original glass will not fit in this part, but this canopy will make your Shuttle look more complete.Side Hatch Door - comes with pre-applied custom sticker.Front Laser Gun - the ones that clip to the body, not the rotating Wing Guns.Front Handle with Trigger Slot.Trigger for the wing release mechanism (no springs or gears, just the trigger itself).Rear Laser GunRamp - Extendable ramp comes with spring loaded posts for easy installation and removal. This does have small parts you need to install - see pics! Instructions: Canopy - See pictures - place the tabs in, starting diagonally, with one lower and to the front, and the other higher and to the rear. Seat firmly into place. Side Hatch Door - place bottom tabs in slots on the Shuttle, and press FIRMLY on the point indicated in the pictures, NOT the top tab. Pressing at the curve flexes the hatch properly so that things pop into place. Trying to force the top tab in directly may not get everything properly aligned to close. This is true for original side hatches as well! Front Handle/Landing Gear - Once the Front Handle is mounted, it is VERY difficult to remove. It simply slides and clicks into place. If you need to remove it, using very thin shims of plastic and sliding them up along the edge and into the clip area will release them. Or if you can disassemble the Shuttle, you can squeeze the tabs from the inside to release them. Rear Laser Gun - For the Rear Laser Gun, I find one side seems to start in better than the other, at least on my Shuttle. If one side doesn't start in easy, start with the other side. Once that side's tab is in place, VERY FIRMLY press in the other side - this may take some force, but it WILL click into place. Once set in, wiggle it left to right to make sure it's centered and both tabs are holding.To remove, firmly pull straight out taking care not to yank on the gun barrels - they can and will break if mishandled. Front Laser Gun - press it firmly into place. To remove, firmly pull straight out taking care not to yank on the gun barrels - they can and will break if mishandled. Ramp - The ramp comes with 2 posts and a spring. Slide the spring into the hole of the ramp. Place one post in one side, and the other post in the other side. Nothing holds these parts in place until the ramp is installed so be careful not to lose these parts. Place one post in its corresponding hole in the shuttle, holding the ramp at an angle. Press the other post in to the ramp, then slide that side up into its corresponding hole as well. Once properly set, the spring will press and hold the 2 posts into proper locking position. Trigger - To install the trigger, you do need to carefully disassemble your Shuttle. I have an instructional video here:https://youtu.be/mzX6oeY_PhY. Once disassembled, place the spring in the trigger's slot, and place into position in its retainer clips. The trigger does not function well until the top parts of the Shuttle are re-assembled, as they hold the wing release system in place. These parts are all my own design. My goal is to make items that closely resemble the originals, are easy for me to make, and cheap for you to buy. As such, if you want original parts, please buy original parts. If you want parts that will make your Imperial Shuttle look good for display and don't want to spend a lot of money or do a lot of work painting them to match, these parts are for you! I try to create custom replacement parts that are good stand ins for diorama/display purposes. SAVE MONEY, combine shipping! Add all items from my store to your cart BEFORE paying, and eBay will automatically combine shipping for you. These 3D printed items will have visible layer lines as you can see in the photos, and may have other minor visual defects from the printing process. The materials I print with are all sand-able and paintable. They are easy for you to custom paint if desired, but they are a close enough match that they look good as is. Visit my eBay store for other hard to find vintage Star Wars parts, repair kits, and vehicle wall mounting hangers! About Galactic Collector: I am a collector of vintage Star Wars action figures, vehicles, and playsets. I regularly restore vintage pieces. I never part out complete items. I often buy broken/damaged/parts lots for salvage, and will resell leftover parts from those to hopefully benefit other restorers out there.